Introduction
We all hope than nothing fails on our NordicTrack treadmill. Nonetheless, it would be best if you prepare yourself in case these problems come. Regardless of the changes or maintenance practices, you invest on your NordicTrack treadmill, at times, you might find yourself in dire need of resetting your treadmill. Some of these issues involve simple malfunctions that require simple troubleshooting steps to repair. But do you really know how to reset NordicTrack Treadmill?
If you still got your user manual- you are lucky. Refer to it as all instructions are well highlighted there. However, if you don’t have your user manual- this article will act as your guide throughout the resetting process. Typically, resetting a NordicTrack Treadmill is quite simple. All you need to know is to turn it on and where the reset buttons are. Follow through to learn to reset your best treadmill.
How to Turn on NordicTrack Treadmill?
If your treadmill’s console is not switched on, it means you cannot use any other controls. First, check that you have plugged your machine to a power source. Make sure you insert the magnetic for safety reasons. If already fixed, pull it out and re-insert and see if it resets the problem.
Problem Not Yet Fixed?-Where is the Reset Button Located?
Check if your power source is working before making any conclusions. Plug another electronic and see if it works. If your wall outlet is working, you need to use the reset button to adjust your machine. The power reset switch is located on the front side of the treadmill near the power cord on the treadmill. Switch it off, wait for about 5 minutes, then switch on the treadmill Press it to reset position, and you are good to go. Besides, try not plugging your treadmill to a GFCI outlet. Note that using a GFCI outlet requires continuous resetting since NordicTrack’s are not compatible.
Console Only Reads Zero- Adjust Reed Switch
If your controls are not functioning correctly or do not show any reading, you need to adjust the reed switch. You will have to use a Phillips screwdriver to locate the reed switch, which is found on the belt pulley’s left side. Remove the motor hood and proceed to adjust the reed switch. When doing this, make sure that you have unplugged the power chord.
You have to rotate the pulley until you have, in-sight, a small magnet near the reed switch. You do not have to remove it- loosen the screw on the switch and as you move it with your other hand to achieve a 1/8-inch gap between the magnet and the switch. Tighten the screw and re-install the motor hood.
Incline Not Working Correctly- Calibrate the Machine
NordicTrack Treadmill is one of the best treadmills, as it can easily be inclined, depending on the user’s requirements. However, your treadmill may fail to respond correctly when you change its incline. You will have to calibrate it. Depending on your model, this process will vary. If yours has standard consoles, continuously press the ‘speed increase’ and ‘stop’ button together. Proceed to insert the safety key then release the buttons.
The treadmill’s belt will rise then return to its lowest level. It will calibrate correctly. For the advanced model with a touch-screen, the process is more straightforward. Go to settings and press ‘calibrate incline,’ and your machine will start the calibration process.
How to Connect an iPad to NordicTrack Treadmill
Being the best treadmill for walking– how can I enhance my workout experience? When learning about resetting your machine, it is essential to learn to connect an iPad. The following steps will serve as guidelines.
First, understand that only an iFit cardio app is compatible with the machine. Install this app, then log in your account details either through your iPad or machine’s console. On the left, upper corner of your display- ta and select a username. Click ‘pair device’ next to the Bluetooth icon and allow it to pair.
Follow the troubleshooting steps displayed in case the device fails to pair the first time. If, after several tries, it does not work out, seek assistance from the iFit support team. After successfully pairing your device, you need to learn about solving a display problem on a console stuck to iFit.
Solving Console Stuck on iFit Screen
When your machine gets stuck on iFit, you might experience freeze problems, boot up loops, or iFit screen freeze. Initially, you can try powering your device off and on. If it fails to work out, you will have to re-install your application. Start your treadmill and stop it once you are stuck on the iFit Screen.
Furthermore, you can try ‘force stopping’ through the settings bar. Try this only when the home screen appears. Press the ‘applications manager’ tab, select your iFit application, and ‘force stop.’ Go back to your home page and press the earth icon to open a browser. The new iFit app will download automatically, and all you have to do now is install. Ensure that all updates are complete before turning down your machine.
Conclusion
This article is a complete guide for you who needs help resetting a NordicTrack Treadmill. Follow through and make sure that you correctly understand each step.